1-1/2 hp Fixed Speed Submersible Turbine Pumps

Specifications

Power Requirements

• 1-1/2 hp Fixed Speed models require single phase, 208-230 VAC, 60 Hertz incoming power
• 1-1/2 hp Fixed Speed models incorporate a starting & running capacitor, with internal bleed resistor, rated 370 Volt, 15 microfarad
• STP-SCI Single Phase Smart Controllers and STP-CBS Single Phase Control Boxes are available for 1 1/2 hp pump control
• Max Motor Draw: 11 amps

Pump Motor

• 1-1/2 hp Fixed Speed, 3450 rpm, multi-stage centrifugal type pump motor with integral, automatic, thermal overload protection
• Available in Standard Pressure (2 stage) model, Max Flow = 100 gpm, Max Pressure = 34 psi
• Available in High Pressure (H150, 3 stage) model, Max Flow = 65 gpm, Max Pressure = 46 psi

Liquid Compatibility

• Max liquid viscosity: 70 SSU @ 60°F (15°C)
• Standard STP (Non-AG) models are UL and cUL listed for fuel mixtures containing up to 15% Ethanol or Methanol, and 20% MTBE, 20% ETBE, or 17% TAME with gasoline.
• STPAG (Alcohol-Gasoline) models are UL and cUL listed for fuel mixtures containing up to 100% Ethanol or Methanol, and 20% MTBE, 20% ETBE, or 17% TAME with gasoline.
• 1-1/2hp Fixed Speed models can also be used with Diesel Fuels, Fuel Oils, Kerosene, Avgas, and Jet Fuels in a non-gelled pourable state.
• All wetted elastomers are made of a high grade, fluorocarbon viton compound.

Standard Features

• 1-1/2 hp Fixed Speed models are available in Variable Length and Fixed Length options
• Check Valve: 2 3/4 diameter fluorocarbon viton seal constructed on cast aluminum body and steel backing washer
• Pressure Relief Valve: available in four pressure relief settings, integral to Check Valve. Standard Model relieves at 40 psi and resets above 35 psi.
• Syphon: venturi type syphon primer supplied with every submersible. Syphon Check Valve and Secondary Syphon sold separately.
• Air Eliminator: every submersible includes tank return path, with one-way check valve, to provide active air elimination
• Electrical Disconnect: electrical yoke for positive contractor disconnect during service

Approvals

• 1 1/2 hp Fixed Speed models are UL and cUL listed
• Consult factory for other applicable approvals

Quality Certification

• Franklin Fueling Systems is an ISO 9001 Certified Manufacturer

Designation System

Click here to view the diagram.

A typical turbine model designation has up to five
components to define the pump being supplied as follows:
STP YYYYY A - B - C
STP = Basic Model Designation

YYYYY = Factory Installed Options
Model designations may include one or more of the
following characters in alphabetical order:
AG = alcohol-gasoline Compatible
(100% ethanol or methanol capable) Note: Standard
models 0% to 15% ethanol or methanol capable
F = Floating suction adapter (1 1/2” NPT Female adapter)
H = High pressure (45 psi deadhead output)
K = Intake filter screen (IFS, factory installed to PMA)
*R = Model R check Valve
(24 psi relief / 22 psi reset for PLLD)
*W = Model W check Valve
(16 psi relief / 13 psi reset for PPM4000)

*Note: If not otherwise specified, all STP models supplied with
standard model check valve (40 psi relief / 35 psi reset for MLD &
LS300)

A = Pump Motor Horsepower Rating
150 = 1 1/2 hp fixed speed

B = Model Length**
VL1 = variable length range #1
VL2 = variable length range #2
VL3 = variable length range #3

**Note: VL2 models fit 94% of all known installations. See 1 1/2 hp
fixed speed model Number tables for specific model length range
details.

C = Riser Pipe Length
Note: Riser pipe length is expressed as two numeric characters
that indicate the total length of the riser in inches. Riser pipes are
available from 7” to 69” in one inch increments (add’l charge for
risers 31” or longer)

Ordering Information

1-1/2 hp Fixed Speed, Variable Length Submersible Turbines Pumps

1. Above models are UL and cUL listed for compatibility with fuel mixtures containing:
STP (Non-AG) = up to 15% Ethanol or Methanol with Gasoline, and 20% MTBE, 20% ETBE, or 17% TAME with Gasoline.
STPAG (Alcohol-Gasoline) = up to 100% Ethanol or Methanol with Gasoline, and 20% MTBE, 20% ETBE,
or 17% TAME with Gasoline.
2. All models are supplied with Standard Check Valve unless factory option “R” or “W” is specified.
3. All above models require Single Phase, 208-230 VAC, 60 Hertz incoming power
* Model Length (B) defined as the dimension from Turbine Manifold bottom to Pump Motor inlet.
** 4” Riser Pipe, if supplied locally, must be 4 1/2” OD by 3/16” wall thickness tubing.
*** For Riser Pipe lengths 31” to 69”, adder charge applies.

Factory Installed Options (specified in Model Number at time of STP order)

Field Installed Options (1-1/2 hp Fixed Speed specific accessories)

*When purchasing STP-SCI or STP-DHI-SCI in equal quantities of Fixed Speed 4 inch STPs, the STP-SCI or STPDHI-
SCI will be invoiced at special discount pricing.