UL Cable Tight™ System
UL Cable Tight™ System
The CableTight™ wire management system provides a true watertight end-to-end solution for electrical, sensor, and data wire management. With the safe and easy electrofusion welding installation process, the HDPE-constructed electrical conduit, entry seals, and sumps are joined together to form one seamless system.
We setup a demonstration course and invited veteran electrical contractors to compare the CableTight™ System with existing electrical conduit systems. Their combined experience includes hundreds of petroleum-specific electrical installations. See for yourself what these experts had to say.
WATERTIGHT WIRE MANAGEMENT SYSTEM
Protect and extend the life of vital petroleum system electrical and data wiring with the CableTight™ wire management system.
Connections between conduit, containment sumps, and fittings are made using the electrofusion welding process.
With the touch of a single button on the welder unit, coils embedded into each fitting are heated and then cooled to weld the individual components into one seamless, watertight connection.
A Smart Welder
The welder calculates the exact settings needed regardless of conduit diameter, component, or ambient temperature.
Easy for the Installer
This process yields consistent and accurate joints and eliminates any messy glues or adhesives that can be affected by weather or temperature.
CableTight™ flexible conduit is constructed of HDPE (high density polyethylene) and comes available in 1,000' or 1,500' coils that can be rolled out into long continuous runs, free of joints.
The long conduit runs help to eliminate potential liquid entry paths from threaded or glued buried joints that need to be made every 10' with traditional PVC or steel conduit.
The conduit’s flexible construction wont crack when bent during cold-weather installation or shatter if accidentally struck by a tool or stepped on after they’ve been laid out on a busy job site.
CableTight™ flexible conduit comes pre-loaded on a compact reel allowing electrical contractors to quickly and easily pull long runs of conduit onsite.
For watertight end connections, the HDPE flexible conduit is electrofusion welded directly to bendable 6' sticks of rigid metal conduit that are either fully coated with PE or have a PE spigot connector depending on the application.
The HDPE elements of the CableTight™ System allow installers to make watertight entries into both polyethylene or fiberglass containment sumps.
For polyethylene sumps, CableTight™ polyethylene entry seals weld directly to the sump’s wall, creating a bond that’s even stronger than either of the two components on their own.
For fiberglass sumps, CableTight™ fiberglass entry seals feature two rigid halves that compress into place on the sump wall, removing exposed rubber that can break down over time.
- Flexible conduit (HDPE): UL Certification of Compliance to UL651A, (HPDE conduit meets NEC 2017 Code Requirements, NFPA 70-2017 (Section No. 514.8 Underground Wiring).
- Rigid metal conduits: UL Certificate of Compliance to UL6 & UL971.
- Electrofusion fittings: UL Certificate of Compliance to UL971.
- Flexible conduit (coils)
- 6' coated rigid metal conduit
- 6' spigotted rigid metal conduit
- Polyethylene sump entry seal
- Polyethylene sump entry seal reducer
- Fiberglass sump entry seal
- Reducing coupler
¾" Cable Tight™ Wire Management System
1" Cable Tight™ Wire Management System
|FFS-0625 (UL) Cable Tight System Datasheet.pdf||5.05 MB|
|FFS-0629 Cable Tight System Certifications Guide.pdf||4.08 MB|
|FFS-0626 (UL) Cable Tight System Brochure_SPC.pdf||4.36 MB|
|FFS-0626 (UL) Cable Tight System Brochure.pdf||15.43 MB|
|FFS-0216 (UL) FFS Product Catalog.pdf||20.28 MB|
|FFS-0807 (EN) Product Catalogue.pdf||48.43 MB|
|FFS-0367 (UL) Site Starters Ordering Guide.pdf||28.44 MB|
|TB1218-03 Cable Tight Welding Clamps.pdf||0.64 MB|
|TB1218-02 Troubleshooting Cable Tight Flexible Conduit.pdf||0.51 MB|
|TB1218-01 Bending Cable Tight Coated Rigid Metal Conduit.pdf||0.43 MB|