APT® ducted double wall rigid entry boots allow you to create watertight connections between APT® 4” XP pipe and double wall fiberglass containment sumps. These boots are easily installed to the sump wall using adhesive (included) without the additional messy fiberglass work required. Rigid entry boots require only a single 3 ¾" entry hole for installation, eliminating the time-consuming process of drilling multiple holes as well as the templates they require.
These electrofusion entry seals weld directly to the walls of polyethylene chambers or sumps. They have been specifically designed to reduce the number of fittings necessary to provide water tight seals between the underground tank sump/chamber and the UPP primary or secondary contained pipe and electrical conduit or duct. The nature of the seal means that after installation it becomes one with the sump, with zero leak paths, creating a 100% leak tight system. The seals are polyethylene based allowing electrofusion of UPP pipework systems directly to the penetration, negating the need for mechanical boots and creating a homogeneous structure of the sump, boot and pipe.
The AST above or below ground transition sump is the practical, environmentally sound solution for remote dispensing from aboveground storage tanks. Steel and flexible piping enter the sump through the APT flexible entry boot. Inside the sump, the steel piping easily connects to flexible piping for a fueltight, continuous run to dispensers or an intermediate sump.
With the PetroTite Standard and Optimum fusion chambers the riser section electrofuses to the base, removing the need for multiple bolt holes and foam gaskets in this area, therefore dramatically reducing the number of potential leak paths. With its simplified assembly, this electrofusion system also reduces the installation time. Welding of the chamber can be performed using UPP electrofusion equipment in approximately six minutes. Once welded and cooled the base and riser of the OCH models become one homogeneous unit, with no mechanical joints and no leak points. The chamber can then be vacuum tested to ensure that it is 100% leak-tight. The Optimum chamber is available with either Deep or Shallow bases, and both will allow for a very easy installation of pipework before the riser is fused into place.
PetroSeal entry boots are two-piece boots for 50mm to 160mm UPP pipework. Using band clips and a backing ring to ensure a perfect fit and the highest quality entry boot.
APT® XP pipework provides a highly flexible pipework solution that makes installation simple and easy in any weather condition or site configuration. XP pipework can be used in both pressure and suction applications, and is ideal for underground service station fuel delivery systems. The XP pipework system features controlled flexibility, even in low temperatures, permitting fast, easy installation.
With the PetroTite Standard and Optimum fusion chambers the riser section electrofuses to the base, removing the need for multiple bolt holes and foam gaskets in this area, therefore dramatically reducing the number of potential leak paths. With its simplified assembly, this electrofusion system also reduces the installation time. Welding of the chamber can be performed using UPP electrofusion equipment in approximately six minutes. Once welded and cooled the base and riser of the OCH models become one homogeneous unit, with no mechanical joints and no leak points. The chamber can then be vacuum tested to ensure that it is 100% leak-tight. The Optimum chamber is available with either Deep or Shallow bases, and both will allow for a very easy installation of pipework before the riser is fused into place.
APT™ brand XP Pipe fittings come in a variety of options for making easy end connections with the flexible pipework system. Each fitting type has been designed to ensure the right solution for any application. The swivel fitting action allows for easy installation in tight containment spaces.
These electrofusion entry seals weld directly to the walls of polyethylene chambers or sumps. They have been specifically designed to reduce the number of fittings necessary to provide water tight seals between the underground tank sump/chamber and the UPP primary or secondary contained pipe and electrical conduit or duct. The nature of the seal means that after installation it becomes one with the sump, with zero leak paths, creating a 100% leak tight system. The seals are polyethylene based allowing electrofusion of UPP pipework systems directly to the penetration, negating the need for mechanical boots and creating a homogeneous structure of the sump, boot and pipe. The spigot on both sides of the 308 allow a second boot to be fitted to the outside as a gravel guard. The seal is fully vacuum and pressure testable ensuring 100% leak free seals and sumps.