EVO™ Series Accessories

EVO 550 - EVO 5000 Accessories.psd

EVO™ Series Accessories

Interface modules, dispenser interface module cables, and paper supplies.

EVO™ 600 and EVO™ 6000 Interface Modules

The EVO™ 600 and EVO™ 6000 come standard with a power supply module and a controller module. Additional interface modules can be installed. Interface modules ordered with an EVO™ will be installed at the factory. If you would like them to not be installed, please order the spare/replacement version of the module. The following guidelines must be followed:

  • EVO™ 600: Six total modules can be installed with a maximum of four intrinsically safe modules and a maximum of three of any one kind of module, except for the UDP Module, which allows for a maximum of four modules.
  • EVO™ 6000: Eleven total modules can be installed with a maximum of nine intrinsically safe modules and a maximum of three of any one kind of module, except for the UDP Module, which allows for a maximum of six modules.

Note: Do not include the Power Supply and Controller Modules when calculating total modules allowed.

Maximum UDP Modules Allowed to Run Concurrently with Probe Modules in a Single EVO™ Console or Expansion Console

The UDP Module is intended to replace the Probe Module for all new system orders. If you are planning to add UDP Modules to an existing EVO™ 600/6000 with Probe Modules, please adhere to the following table:

Existing Probe Modules Allowable UDP Modules
0 6
1 4
2 2
3 0

Intrinsically Safe Modules

Model Number Description
FMP-485IS

RS485 module (EVO™ 600 and EVO™ 6000 only)

FMP-UDP9 UDP Module, 12 inputs, compatible with FMP-LL3-XXX and FMP-LL3-I probes, FMP-UHS and FMP-ULS sensors, and FMP-XXX-U sensors (EVO 600 and EVO 6000 only).
TS-2WSNS 12 input 2-wire sensor module, (Required for FMP-ULS, FMPUHS, TSP-HLS, and FMP-HFS sensors)
TS-3WSNS 8 input 3-wire sensor module, TSP-EIS, TSP-DIS, TSP-DDS, TSP-DTS, TSP-HIS, TSP-MWS and TSP-DVS sensors. Can also support 2-wire sensors
TS-PRB 12 input probe module, (Required for LL2 and LL3 Series Mag probes, VFM flow meters and DMS Mag sensors)
TS-420IB 8 input 4-20 mA module, (Required for LSU500 transducers and VPS and SCCM pressure sensors)
  • -U sensors are not supported on the 2-wire or 3-wire sensor module.

Non-Intrinsically Safe Modules

Model Number Description
TS-10ARLY 6 output 10 Amp relay output module, high power dispensers and SCCM solenoids
TS-420EXP 8 input 4-20 mA module, LSU500E transducers and external devices
TS-ACI 12 input AC input module, (Required for dispenser hook inputs)
TS-IO Input output module, 4 output 4-20 mA, 8 input 3-240 VAC/DC
TS-RLY 8 output 2 Amp relay module, SCCM solenoid and STP control
  • TS-RLY Module is not required for STP control when utilizing turbine pump interface (TPI) communications. The TS-420EXP module requires Controller Module software version 9.5 or greater Do not include Power Supply and Controller Module when calculating total modules allowed.

Dispenser Interface Module Cables

Model Number Description
TSP-BDCBL Bennett® 515 only cable
TSP-GDCBL Gilbarco™ cable
TSP-GSDCBL Gilbarco™ G-Site™ cable
TSP-WDCBL Wayne™ cable

Paper Supplies

Model Number Description
TS-TP2 One box of 5 rolls of thermal printer paper for fuel management system and Tank Sentinel® consoles
TS-TP2C One case of 20 boxes of 5 rolls of thermal printer paper for fuel management system and Tank Sentinel® consoles

Legacy ATG Paper Supplies

Model Number Description
TS-INKRB TS-550 and TS-5000 ink ribbon
TS-TP5000 TS-550 and TS-5000 impact printer paper
TS-TP5000C 12 rolls of impact printer paper
  • T5 Series consoles shipped after 8/2010 have thermal printers.